Storm Sewer & Flood Modeling
Welcome to the Innovyze Stormwater, Sewer, and Flood modeling feedback page.
48 results found
-
RDII Analyst (in ICM)
Provide RDII Analyst without needing to purchase InfoSWMM
24 votes -
Improve ground infiltration simulation parameters.
Could we have a 'Node level affects groundwater infiltration' for the soil store please?
This simulation parameter was introduced to InfoWorks ICM recently to limit infiltration from the ground store to the model. Could this be extended to limit flows from the soil store as well?
As often when are using models for design purposes, infiltration can become excessive in design events compared to verification. Therefore we have to manually reduce soil store inflow, often requiring new limiting discharge orifices and nodes at each subcatchment with GI applied. Thanks19 votes -
Circular sluices/penstocks would also be useful
Similar to the rectangular flap valve request, circular sluices would avoid workarounds trying to estimate the rectangular equivalent to a half closed circular penstock (or worse still a half closed egg shaped penstock)
19 votes -
Ability to use variables in range RTC rules
For RTC range rules, we want to be able to use variables instead of constant values for the minimum and maximum values.
17 votes -
Calculating volume storage on river reaches
In the application of ICM, we often count the regulation volume of river channels.But at the moment we can only calculatethe total available volume of channels/river reaches between two cross sections by using length and cross sectional areas.If the number of river sections is very large in the model,it will take a lot of time and effort to accomplish this work. It would be great to have the tool to calculate volume storage on river reaches automatically.
17 votes -
bottom opening
Beside an upstanding vertical orrifice, it would be practical to be able to implement horizontal 'bottom holes' from one node to an underlaying node. e.g when a ditch can drain to an underlying conduit by means of a bottom opening. This might be a more straight forward implementation then the weir circumference workround method which is now often used. if possible both circular and rectangular.
16 votes -
Simulation engine control update
Since the beginning of ICM and allowing to send simulation to other computers in the network, there was a need for knowing exactly who is currently sending simulations and to which computer. Please update the ICM with this improved functionality for the normal user, not for admin only. These people are the ones who send simulation to the network, not IT people!
15 votesThank you for the addition of this request, we are in discussions about how this might be achieved as the level of awareness of tasks is varied between agents. Would a dashboard showing who sent which simulation where (which are still ongoing) be sufficient? This would be without the progress those simulations have already made available as a first step.
-
Conveyance on cross section lines
Provide cross section conveyance for each cross section
14 votes -
Bank line ground model update from within properties view
Make update from ground model possible from within properties view (as is already possible for cross sections)
13 votes -
blockage
Applying pipe blockage is a standard required in Australia and the functionality in ICM to do this is not user friendly (using blockage links). A simple % pipe blockage in the conduit properties should really be an option. This is particular the case for cross drainage and also orifice and pipes leaving detention basins (where a pit isnt used)
12 votes -
Add US and DS HGLs for links
Currently ICM link results report the US and DS total head values. As a user, I'd like to see the HGL at the US and DS locations consistent with the node results. This would be useful on graphs and long sections.
11 votes -
Wide "Oval" shape ID
conduit shape ID "Oval" only allows Height > With. So for "horizontally" wide oval conduits a new conduit shape has te be defined. It would be practical if the standard "Oval" also allows a with greater than the hight.
11 votes -
Orifice to limit flow in both directions
A limiting discharge set on an orifice should limit flow in both directions. Currently, the orifice limits flow in the forward direction; however, flow can go in the reverse direction at an unlimited rate. Hydraulically, if there is a physical feature that limits flow, it seems that it would limit to (for example) <10 l/s and > - 10 l/s.
11 votes -
Infoworks - Pipe grade calculator
Pipe grade calculator between US and DS inverts, Ultimately having the ability to calculate downstream or upstream inverts over a long network based on a specified grade from either a DS or US invert level as a starting point.
10 votes -
Can ICM add particle tracking module?
When there are pollutants that enter a system from various sources then it would be good to have pollutant tracing functionality which shows the source and the pollutant moving through the system, giving an idea of the rate at which it travels and impacts areas downstream.
10 votes -
Merge pond and storage nodes and increase their functionality
Pond nodes:
- allow variable infiltration at different levels (up to 3 different rates)
- allow variable perimeter with level i.e. plan area through which side infiltration can occurs can vary
- no porosity functionStorage nodes:
- 1 porosity value (which only works below ground, above ground it is assumed to be 100%)
- fixed perimeter for infiltration i.e. assumes cylindrical shape for infiltration (despite the plan area changing with level)
- fixed infiltration rate (no change with height)It is not possible to model both porosity and a change in infiltration with height.
I propose that pond and…
9 votes -
Pipe collision check
Client feedback: an automatic check for colliding pipes would be highly appreciated to avoid nightmares in the construction.
9 votes -
Pump Station Modelling
Infoworks ICM pump station modelling principle is very basic, adding a pump between two nodes is highly hypothetical. There is no way to add pump station head losses.
I would like to suggest incorporating pump station modelling (for Rotodynamic pumps) with pump curve and system curve theory. Then the model results would be much more realistic.
There must be a tool to incorporate all the accessories in pump stations, between two nodes. Like pump station type, drywall wet well. And Parameters to calculate Pump suction and discharge losses, like all fittings, non-return valves, discharge valves, flow meters etc. This would…7 votes -
Allow the user to choose the flood type of pond or storage nodes
Allow the user to choose the flood type of pond or storage nodes from a drop down as is the case for manholes. As opposed to the current state where the flood type depends on the relationship between the highest level entry in the storage array and the ground level of the node.
From help file: "Storage nodes or ponds can flood. If the highest level entry is below ground level, the pond is considered to have a roof at that level and is therefore sealed. If the highest level entry is equal to the ground level then any water…
7 votes -
Update Storage array from ground model
Provide the ability to update a storage array (curve) from ground model without destroying manually entered data
7 votes